UNI-T UT501 Manuel d'installation

I/F 501INTERFACE UNITINSTALLATION AND OPERATION GUIDESoftware Revision 1.05, Version AINTRODUCTION The I/F 501 interface unit allows a variety of comu

MIDI TO AMX-192In this application, MIDI is converted to AMX 192.CONNECTOR OPERATIONMicroplex IN Not usedMicroplex OUT Not UsedDMX IN Not used*DMX out

RS-232 to MICROPLEX and DMX 512In this application, a computer may send simple ASCII commands to operate individual dimmer channels.CONNECTOR OPERATIO

RS-232 TO AMX 192In this application, a personal computer may send ascii commands to operate individual dimmer channels.CONNECTOR OPERATIONMicroplex

LUMA-NET to MICROPLEXIn this application, Microplex or DMX is mixed with LUMA-NET and transmitted as Microplex.CONNECTOR OPERATIONMicroplex IN Input M

LUMA-NET to DMX-512In this application, Microplex or DMX is mixed with LUMA-NET and transmitted as DMX 512.CONNECTOR OPERATIONMicroplex IN Input Micro

LUMA-NET to AMX - 192In this application, Microplex or DMX is mixed with LUMA-NET and transmitted as AMX-192.CONNECTOR OPERATIONMicroplex IN Input Mic

ANALOG TO / MERGED WITH DMX 512 and MICROPLEXIn this application, 0 to 10VDC is converted to Microplex or and DMX 512..CONNECTOR OPERATIONMicroplex I

ANALOG TO AMX-192In this application, 0 - 10VDC is converted to AMX 192.CONNECTOR OPERATIONMicroplex IN Input MicroplexMicroplex OUT Not UsedDMX IN

AUTOCHASE TO MICROPLEX AND DMX 512.In this application, the unit serves as a stand alone chaser.CONNECTOR OPERATIONMicroplex IN Not UsedMicroplex OUT

RS-232 AUTO-CUEING TO MICROPLEX AND DMX.In this application, the unit serves as a stand alone programmable memory lighting controller with precise ti

Front Panel1 DC Power input - Connect 15VDC (+ tip, - ring) 250ma here. (Supplied with unit.)2 Address - Controls translation of adresses (and other s

LUMA-NET 404CP EMULATION WITH EXTERNAL CONTACTS.In this application, the unit serves as a 404CP panel with external contact closures. CONNECTOR OPERAT

LUMA-NET SOFTWARE INTERFACE.This application is for use with the Luma-net Computer Software. This unit serves as the interface between thecomputer a

Lumanet Channel number codes / dipswitch settings.Multiply channel listed by increment required. Subtract one for Luma-net network ID no.0 - switch do

DMX 512 Channel number codes / dipswitch settings.0 - switch down, 1 - switch up1st DMXChannelDipswitch12345671st DMXChannelDipswitch12345671st DMXCha

ASCII Cues ImplementationOverviewFollowing are the rules for editing ASCII Cues as implemented on the IF501, software revision 1.00:If you use a word

DOWNThis keyword specifies the fade down time of the previous cue. This keyword must be followed by a space andthe time in the range of ‘‘0" to

WARRANTYNSI Corporation Limited Warranty NSI Corporation warrants new electronics products to be free from defective materials and workmanship for ape

JUMPER LOCATIONSPCB locations of jumpers / internal connectorsINTERFACE UNITSoftware Revision 1.05, Version A JUMPER LOCATIONSNSI CORPORATION 3

INPUT -> OUTPUTCONFIGSWITCHd-downu-up1234P4P5P7 JP1 JP6JP7JP8JP9JP10 JP11 JP12 DMXOUTCONNDEFAULT SETTINGSdddd OFF ON 6 2-3 2-3 2-3 2-3 1-2 JP4MPX -

PINOUTS Pinouts of the various connectorsINTERFACE UNITSoftware Revision 1.05, Version A PINOUTS NSI CORPORATION 5

MICROPLEX TO DMX 512In this application, Microplex is converted to DMX-512. The Microplex is then retransmitted.CONNECTOR OPERATIONMicroplex IN Input

MICROPLEX TO AMX 192In this application, Microplex is converted to AMX-192. The 5 pin XLR may be replaced with a 4 pin XLR(USITT) if desired.CONNECTO

DMX 512 TO MICROPLEXIn this application, DMX 512 is converted to Microplex..CONNECTOR OPERATIONMicroplex IN Not usedMicroplex OUT Output Microplex (64

MIDI TO MICROPLEX and DMX 512In this application, MIDI note commands are converted to Microplex and DMX 512 dimmer levels.CONNECTOR OPERATIONMicroplex